Merge upstream v1.17.0 (origin/main) into the analyzer/BLE fork
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
This commit is contained in:
commit
774676248b
348 files changed
+11263
-1658
No files matched your search
+52
-1
@@ -19,6 +19,7 @@ This document provides an overview of CLI commands that can be sent to MeshCore
|
||||
- [GPS](#gps-when-gps-support-is-compiled-in)
|
||||
- [Sensors](#sensors-when-sensor-support-is-compiled-in)
|
||||
- [Bridge](#bridge-when-bridge-support-is-compiled-in)
|
||||
- [Ethernet](#ethernet-when-ethernet-support-is-compiled-in)
|
||||
|
||||
---
|
||||
|
||||
@@ -311,6 +312,20 @@ in order of preference:
|
||||
|
||||
---
|
||||
|
||||
#### View or change the LoRa FEM receive-path gain state on supported boards
|
||||
**Usage:**
|
||||
- `get radio.fem.rxgain`
|
||||
- `set radio.fem.rxgain <state>`
|
||||
|
||||
**Parameters:**
|
||||
- `state`: `on`|`off`
|
||||
|
||||
**Notes:**
|
||||
- This controls the external LoRa FEM receive-path LNA where the board supports it.
|
||||
- This is separate from `radio.rxgain`, which controls the radio chip receive gain mode.
|
||||
|
||||
---
|
||||
|
||||
### System
|
||||
|
||||
#### View or change this node's name
|
||||
@@ -325,7 +340,7 @@ in order of preference:
|
||||
|
||||
**Default:** Varies by board
|
||||
|
||||
**Note:** Max length varies. If a location is set, the max length is 24 bytes; 32 otherwise. Emoji and unicode characters may take more than one byte.
|
||||
**Note:** Advertised names can use up to 23 bytes when location is included and 31 bytes otherwise. Emoji and Unicode characters may take more than one byte. Names that exceed the available advert space are truncated at a valid UTF-8 code point boundary.
|
||||
|
||||
---
|
||||
|
||||
@@ -612,6 +627,20 @@ in order of preference:
|
||||
|
||||
---
|
||||
|
||||
#### Enable or disable hardware Channel Activity Detection (CAD)
|
||||
**Usage:**
|
||||
- `get cad`
|
||||
- `set cad <on|off>`
|
||||
|
||||
**Description:** When enabled, the radio performs a hardware Channel Activity Detection scan before transmitting and defers if the channel is busy. Runs independently of `int.thresh` — either, both, or none may be active.
|
||||
|
||||
**Parameters:**
|
||||
- `on|off`: Enable or disable hardware CAD
|
||||
|
||||
**Default:** `off`
|
||||
|
||||
---
|
||||
|
||||
#### View or change the AGC Reset Interval
|
||||
**Usage:**
|
||||
- `get agc.reset.interval`
|
||||
@@ -1170,3 +1199,25 @@ repeater advertises. Build-time knobs: `GPS_DUTY_SYNC_INTERVAL_SECS` (1800),
|
||||
**Note:** Returns an error on boards without power management support.
|
||||
|
||||
---
|
||||
|
||||
### Ethernet (when Ethernet support is compiled in)
|
||||
|
||||
Ethernet support is available on RAK4631 boards with a RAK13800 (W5100S) Ethernet module. Use the `_ethernet` firmware variants (e.g. `RAK_4631_repeater_ethernet`) to enable this feature.
|
||||
|
||||
---
|
||||
|
||||
#### View Ethernet connection status
|
||||
**Usage:**
|
||||
- `eth.status`
|
||||
|
||||
**Output:**
|
||||
- `ETH: <ip>:<port>` when connected (e.g. `ETH: 192.168.1.50:23`)
|
||||
- `ETH: not connected` when Ethernet is not active
|
||||
|
||||
**Notes:**
|
||||
- Available on repeater and room server firmware only. Companion radio ethernet firmware does not expose a CLI.
|
||||
- The Ethernet interface obtains an IP address via DHCP automatically on boot.
|
||||
- A TCP server listens on port 23 (default) for CLI connections.
|
||||
- Connect with any TCP client (e.g. `nc`, PuTTY) to access the same CLI available over serial.
|
||||
|
||||
---
|
||||
Reference in new issue
Block a user