Small one after v1.17.0: 57 files, +825/-200, and it merged with no conflicts at
all. Unlike 1.17.0, the release tags sit directly on origin/main, so no
`-s ours` is needed for git describe to see the release.
What matters for our nodes:
* fix-rxgain-setting-post-agc-reset -- rx gain no longer resets after an AGC
adjustment. The release notes ask repeater admins to verify radio.rxgain (and
the new radio.fem.rxgain) after updating, so that goes on the post-flash list.
* NRF52 CC310 crypto is initialised once instead of on every call, and several
NRF52 pin maps were corrected.
* New 'get/set radio.fem.rxgain/txgain' CLI commands (companion cannot configure
them yet).
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Upstream shipped companion/repeater/room-server v1.17.0 today; its tree is
identical to origin/main, so that is what this merges. Our base was 7 Jul
(7b566670), i.e. 350 files / +11k lines of upstream behind.
Conflicts and how they were settled:
* Mesh.cpp -- upstream split the dedup into wasSeen() + explicit markSeen().
Kept BOTH: their new call pair AND our payload-length bound on the TRACE
path-hash read, which is what stops a crafted short TRACE from steering
isHashMatch() past the buffer.
* companion_radio/main.cpp -- upstream grew its own MultiSerialInterface
(BLE + USB + WiFi + Ethernet registered side by side), which is a superset
of the SerialDualInterface we backported from PR #1779. Took theirs whole;
our copy is now dead code. NOTE: envs that relied on the backport for a USB
console alongside BLE now need an explicit -D ENABLE_USB_INTERFACE.
* ui-new/UITask.cpp -- isSerialEnabled() was renamed isBluetoothEnabled()
upstream and DisplayDriver::RED became UIColor::warning_txt. Same intent
either way: no BT pin on screen while Bluetooth is off.
* EnvironmentSensorManager.cpp -- upstream fixed the millis() wrap on the GPS
update timer in the exact line our gpsDutyLoop() call sits on. Kept both,
with their wrap-safe compare.
* NRF52Board.cpp -- upstream independently arrived at the same sd_temp_get()
fix for SoftDevice-protected TEMP. Took their form, kept our comment, which
is the only place recording WHY (APP_MEMACC fault -> reboot on telemetry).
* RadioLibWrappers.{h,cpp}, simple_repeater/main.cpp -- add/add. Their
configSideDetectors()/performChannelScan()/external watchdog next to our
irqDoneMask()/probeDio1()/BLE pump/WDT feed. The repeater console keeps the
1032-byte reply buffer for paged analyzer output and now clears it, since a
static buffer would otherwise reprint the previous reply.
* .vscode/extensions.json -- deleted upstream, and it is in .gitignore; our
only change was a comment. Gone.
Built clean: Xiao_x1_rpt, Xiao_x2_cmp, Xiao_x3_obs, SenseCap_s1_rpt,
T1000E_cmp_cz. Not flashed to anything yet.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
PA PL1 re-targets the PA's DC-DC supply rail rather than selecting a
logic-level gain, and the serial CLI is serviced on every main-loop pass
regardless of whether a transmit is in flight. A `set radio.fem.txgain`
write could therefore move the rail mid-transmit, while the SX1262 was
still driving the PA at full input power.
Record the requested level in setPAGainEnable() and drive the pin from
setTxModeEnable(), which runs from onBeforeTransmit() ahead of
startTransmit(). The level only matters while transmitting, so deferring
costs nothing.
Document that the pref is saved immediately but applied at the next
transmit, so `get radio.fem.txgain` can lead the hardware until then.
Extract the inline cursor-walk in handleRegionCmd into file-local
helpers (skipSpaces, rtrimSpaces, takeToken, splitNameJump,
processRegionDefSegment), grouped immediately above the consumer.
Behavior is identical; addresses PR #2540 review feedback on
readability.
Tighten the region def docs: collapse five Note callouts into three
grouped paragraphs (Behavior / Existing regions / Limits), add a
case-sensitivity caveat plus an error example, note the cursor reset
between split commands, and use generic placeholder names.
Add a new command `region bulk` for defining region hierarchies in a single line. This command allows users to create multiple regions in a single message. Updated the documentation to include usage examples and detailed parameter descriptions.