Commit Graph
918 Commits
Author SHA1 Message Date
Ryan Gregg 83779fb197 Fix POE boot failure on RAK4631 Ethernet builds
Drive WB_IO2 (slot power switch) HIGH via early constructor before the
Arduino framework initializes. Without this, the board brownouts on
POE-only power because the slot MOSFET isn't enabled early enough for
the RAK13800 POE module to deliver power to the baseboard.

Also remove the W5100S hardware reset pulse from Ethernet init — the
chip comes out of power-on reset cleanly, and toggling reset kills
the PHY link which breaks POE power delivery.
2026-03-20 17:56:04 -07:00
Ryan GreggandClaude Opus 4.6 26c576b014 Merge upstream/dev into rak-ethernet
Resolve conflicts: keep both Ethernet CLI and SenseCAP power-off
button code in repeater, keep both Ethernet docs and power management
CLI docs.

Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
2026-03-13 11:07:09 -07:00
Scott Powell 09bba14d96 Merge branch 'main' into dev 2026-03-12 18:14:56 +11:00
ripplebiz abee981012 Merge pull request #1873 from Specter242/codex/sensecap-solar-led-poweroff-parity
sensecap solar: add poweroff/shutdown support and nrf52 PM parity
2026-03-12 18:13:14 +11:00
Ryan Gregg 359832ab5b Updates based on PR review feedback from liamcottle 2026-03-10 22:35:31 -07:00
Ryan GreggandClaude Opus 4.6 7dcdecbd4c Address PR review feedback for Ethernet support
- Add #pragma once to SerialEthernetInterface.h
- Rename TCP_PORT to ETH_TCP_PORT with #ifndef guard
- Fix typos: "initalizing" → "initializing"
- Fix #elif without condition → #else for STM32 block
- Replace infinite loop on ETH init failure with halt()
- Remove heartbeat Serial.print(".") output
- Remove dead beginETH() call (ETH_ENABLED, not RAK_ETH_ENABLE)
- Comment out MESH_DEBUG and ETH_DEBUG_LOGGING build flags

Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
2026-03-10 20:43:59 -07:00
Ryan GreggandClaude Opus 4.6 d0d415d5f6 Add native Ethernet support for RAK4631 repeater, room server, and companion
Add W5100S Ethernet adapter support for RAK4631-based firmware, enabling
TCP CLI access on port 23 as an alternative to BLE/Serial connections.

- New SerialEthernetInterface for nRF52 with DHCP, reconnection handling,
  and shared WB_IO2 power pin management with GPS module
- Ethernet build targets for repeater, room server, and companion firmware
- Prevent GPS from toggling WB_IO2 when Ethernet module is active
- CI build check for all three ETH firmware targets

Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
2026-03-10 20:43:59 -07:00
MGJ 92ca3da7cc Add support for the GAT562 Mesh Tracker Pro device 2026-03-09 14:25:24 +08:00
MGJ 7667c7cc9c Add support for the GAT562 Mesh Tracker Pro device 2026-03-09 13:13:41 +08:00
Confi 55cde28704 sensecap_solar: fix LED definitions (white=11, blue=12) 2026-03-07 09:59:30 +01:00
Liam Cottle e225f6eb8f Merge pull request #1589 from marnick-hartgers/gps_sencecap_solar_p1
Added gps support for Sensecap p1 solar
2026-03-07 21:31:38 +13:00
Liam Cottle 6f0bc8b611 Merge pull request #1936 from Quency-D/dev-heltec-tracker-v2
Update Heltec Tracker v2 to version KCT8103L.
2026-03-07 17:59:19 +13:00
Liam Cottle 541dad8202 Merge pull request #1391 from R6DJO/fix_t1000-e_temp
T1000-E: Negative temperature values incorrectly displayed due to char signedness
2026-03-07 16:49:54 +13:00
Liam Cottle 65d57abcee Merge pull request #1364 from weebl2000/pass-rtc_clock-to-locationprovider
Pass rtc_clock to MicroNMEALocationProvider in all variants
2026-03-07 16:41:29 +13:00
Quency-D edca686339 Fixed a bug in the LORA_TX_POWER comment. 2026-03-06 16:04:47 +08:00
Quency-D cc48c8c91d Update Heltec Tracker v2 to version KCT8103L. 2026-03-06 14:19:07 +08:00
Wessel Nieboer b1de55a3c5 Pass rtc_clock to all MicroNMEALocationProvider instances
Enable GPS time synchronization across all variants by passing
&rtc_clock to MicroNMEALocationProvider. When GPS gets a valid
fix, the RTC clock is now updated automatically every 30 minutes.

Updated 16 variants: rak4631, lilygo_tbeam_SX1262, rak_wismesh_tag,
lilygo_tbeam_supreme_SX1262, thinknode_m3, heltec_v4, thinknode_m1,
lilygo_tbeam_SX1276, meshadventurer, nano_g2_ultra, heltec_v3,
promicro, xiao_c3, heltec_tracker_v2, keepteen_lt1, heltec_mesh_solar.
2026-03-03 15:45:07 +01:00
Wessel Nieboer 55b31334e2 and buildscript 2026-03-03 15:37:33 +01:00
Wessel Nieboer af7d4e585d and board! 2026-03-03 15:37:33 +01:00
Wessel Nieboer d261c1fd8c Fix ikoka handheld build
The extends was wrong.
2026-03-03 15:37:32 +01:00
Liam Cottle 434ef6d94a Merge pull request #1836 from weebl2000/fix-rak3401-sky66122-11-fem
Fix RAK3401 SKY66122-11 FEM control: enable CSD/CPS for proper PA/LNA operation
2026-03-03 23:51:42 +13:00
Liam Cottle 59d8f7346f Merge pull request #1600 from weebl2000/heltec_deep_sleep_lna
Hold GC1109 PA_POWER during deep sleep for LNA RX wake
2026-03-03 23:20:22 +13:00
Wessel Nieboer 042658a0c2 Add GPS support Heltec Wireless Tracker v1.x
Pin mapping verified against HTIT-Tracker V0.5 schematic:
- GPIO35 (GPS_EN): N-ch MOSFET drives P-ch high-side switch, active HIGH
- GPIO36 (GPS_RST): hardware reset, active LOW
- GPIO33/34: UART TX/RX

Delegates power management to MicroNMEALocationProvider begin()/stop()
which independently controls GPS power via GPS_EN and shares VEXT with
the display through RefCountedDigitalPin.
2026-02-28 19:09:28 +01:00
Wessel Nieboer 2d216b7115 Fix pin mapping & TX switch (it's DIO2) 2026-02-28 19:09:06 +01:00
Wessel Nieboer 809f8badf1 Drive CTX low first 2026-02-28 19:09:06 +01:00
Wessel Nieboer a114d515e4 Add SX126X_REGISTER_PATCH for RAK3401 2026-02-28 19:09:06 +01:00
Wessel Nieboer 7af21122c4 Fix RAK3401 SKY66122-11 FEM control: enable CSD/CPS for proper PA and LNA operation
The RAK13302 1W module uses a Skyworks SKY66122-11 front-end module with
three digital control pins (CSD, CTX, CPS) that must be actively driven
by the host MCU. The previous code only managed CTX (GPIO 31) — toggling
it for TX/RX — but never initialized CSD (GPIO 24) or CPS (GPIO 21),
leaving them floating with no pull-up/pull-down resistors on the PCB.

With floating CSD and CPS, the SKY66122 was in an undefined operating
mode:
- The 30 dB TX PA may not have been reliably engaging
- The 16 dB RX LNA was never reliably active, degrading receive
sensitivity
2026-02-28 19:09:06 +01:00
Wessel Nieboer c7fd4ee9e2 Add 1ms delay after powering PA (cold-boot) 2026-02-28 19:05:31 +01:00
Wessel Nieboer 75730e60db Hold GC1109 PA_POWER during deep sleep for LNA RX wake
The GC1109 FEM needs its VFEM_Ctrl pin held HIGH during deep sleep
to keep the LNA active, enabling proper RX sensitivity for
wake-on-packet. Without this, the LNA is unpowered during sleep
and RX wake sensitivity is degraded by ~17dB.

Release RTC holds in begin() after configuring GPIO registers
(not before) to ensure glitch-free pin transitions on wake.

Trade-off: ~6.5mA additional sleep current for significantly
improved wake-on-packet range.
2026-02-28 19:05:31 +01:00
Liam Cottle ae2d9c40cc Merge pull request #1569 from IoTThinks/MCdev-Fixed-Incorrect-Release-of-RefCountedDigitalPin
Fixed RefCountedDigitalPin.h and SSD1306Display for Heltec v4
2026-02-28 17:35:17 +13:00
Specter242 ed3e413a54 sensecap solar: stabilize wake pin and add button hold poweroff 2026-02-27 22:51:19 -05:00
Specter242 1dc7bb9680 sensecap solar: add poweroff command and board power/LED parity 2026-02-27 22:12:12 -05:00
Scott Powell 2c167d4479 * misc 2026-02-24 21:30:04 +11:00
callum5892 648c9bb818 Added build flags for M5Stack Unit C6L
Enabled USB-CDC on boot for M5Stack_Unit_C6L_companion_radio_usb to fix serial connection issues
2026-02-23 17:31:18 +00:00
ripplebiz f920af9f80 Merge pull request #1792 from ElectroMW/feature/t-beam-supreme-improvements
T-Beam Supreme - Make full use of board's 8MB Flash and add Companion WiFi target
2026-02-23 12:38:56 +11:00
Sam Koucha 006ff78cd7 Make full use of board's 8MB Flash and add companion WiFI target 2026-02-22 18:14:39 +00:00
Sander van Grieken e57c22a0fb add companion usb build target for Heltec Wireless Tracker 2026-02-22 17:57:36 +01:00
Kevin Le c9b9fbd8bb Reverted to use GPIO 17, 18 as I2C for Heltec v4 repeater 2026-02-18 22:38:24 +07:00
Kevin Le a989a2bb0c Disabled periph_power for Heltec v4's display 2026-02-18 22:32:01 +07:00
Kevin Le ade1c8f7c2 Set back PIN_VEXT_EN_ACTIVE=HIGH 2026-02-18 22:32:01 +07:00
3DPGG 53e92916d9 Fix LilyGo_TLora_V2_1_1_6_terminal_chat build
This change addresses two issues. The first is that the
LilyGo_TLora_V2_1_1_6_terminal_chat build would try to compile
simple_repeater/MyMesh.cpp. All other examples of terminal chat
targets are instead building simple_secure_chat/main.cpp . This
change would align this build to the rest of the builds.

The second issue, found during the course of investigating the
first, stems from simple_repeater/MyMesh.cpp using the
MAX_NEIGHBOURS #define to control whether the neighbor list is kept.
Repeaters that keep this list must define this value, and if the
value is not defined, then all neighbor-related functionality is
compiled out. However, the code that replies to
REQ_TYPE_GET_NEIGHBOURS did not properly check for this #define,
and thus any target that compiles simple_repeater/MyMesh.cpp
without defining MAX_NEIGHBOURS would get an undefined variable
compilation error.

As a practical matter though, there are no targets that compile
simple_repeater/MyMesh.cpp AND do not define MAX_NEIGHBOURS,
except this build due to the first issue. As a result, the
second issue is addressed only as a matter of completeness. The
expected behavior with this change is that such a repeater would
send a valid reply indicating zero known neighbors.
2026-02-16 18:10:29 -08:00
recrof 2bb616689c fix M5Stack Unit M6L build errors 2026-02-15 11:25:27 +01:00
ripplebiz 4ece286c9b Merge pull request #1669 from Azuresword/fix/wio-tracker-l1-grove-sensor-v2
Fix WioTrackerL1 BLE companion: route sensors to Grove I2C bus (Wire1)
2026-02-15 15:55:25 +11:00
Liam Cottle 3ac7af47e0 Merge pull request #1671 from recrof/rak3112-fix
fix: usb and ui for rak 3112
2026-02-12 11:39:27 +13:00
Rastislav Vysoky 562a245695 fix usb and build for rak 3112 2026-02-11 09:34:41 +01:00
dylanandClaude Opus 4.6 8535cf5726 Fix WioTrackerL1 BLE companion: route sensors to Grove I2C bus (Wire1)
Sensors connected via the Grove I2C connector (D18/D17) were not detected
because the firmware scanned the OLED I2C bus (Wire, D14/D15) by default.
Adding ENV_PIN_SDA/SCL flags directs EnvironmentSensorManager to use Wire1,
matching the physical Grove connector pinout.

Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
2026-02-11 14:12:48 +08:00
ripplebiz f4b4b9addc Merge pull request #1611 from weebl2000/semtech-patch-tracker-v2
Enable register patch heltec tracker v2
2026-02-11 14:04:58 +11:00
Snayler eb21c51f71 Enable TX LED for LilyGo LoRa32 V2.1_1.6
Working on my device, green TX LED starts blinking every time I transmit
2026-02-09 23:20:29 +00:00
ripplebiz 469c2e7332 Merge pull request #1570 from Quency-D/fix-heltec-power-consumption
Fix heltec-v4 power consumption
2026-02-09 16:49:49 +11:00
ripplebiz 7571558af5 Merge pull request #1605 from ViezeVingertjes/kiss-modem-spec-compliance
Kiss modem spec compliance
2026-02-09 16:45:20 +11:00