96 lines
2.8 KiB
C++
96 lines
2.8 KiB
C++
#include <Arduino.h>
|
|
#include <SPI.h>
|
|
#if ENV_INCLUDE_INA219
|
|
#include <Wire.h>
|
|
#endif
|
|
#include "target.h"
|
|
|
|
LilyGoT3STM32Board board;
|
|
RADIO_CLASS radio = new STM32WLx_Module();
|
|
WRAPPER_CLASS radio_driver(radio, board);
|
|
VolatileRTCClock rtc_clock;
|
|
#if ENV_INCLUDE_INA219
|
|
EnvironmentSensorManager sensors;
|
|
#else
|
|
SensorManager sensors;
|
|
#endif
|
|
DISPLAY_CLASS display;
|
|
// PH3 is also BOOT0: the board's button is active high with an external pull-down.
|
|
MomentaryButton user_btn(PIN_USER_BTN, 1000, false);
|
|
UITask ui_task(&board, &display);
|
|
|
|
static const uint32_t rfswitch_pins[] = {
|
|
PB2, PB6, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC
|
|
};
|
|
static const Module::RfSwitchMode_t rfswitch_table[] = {
|
|
{STM32WLx::MODE_IDLE, {LOW, LOW}},
|
|
{STM32WLx::MODE_RX, {HIGH, LOW}},
|
|
{STM32WLx::MODE_TX_HP, {LOW, HIGH}},
|
|
END_OF_MODE_TABLE,
|
|
};
|
|
|
|
void LilyGoT3STM32Board::begin() {
|
|
STM32Board::begin();
|
|
|
|
#if ENV_INCLUDE_INA219
|
|
// These builds remap Wire to PB7/PB8; PA9/PA10 are used by USART1.
|
|
Wire.begin();
|
|
#endif
|
|
|
|
// The SD card shares SPI1 with the OLED; keep it deselected.
|
|
digitalWrite(PA4, HIGH);
|
|
pinMode(PA4, OUTPUT);
|
|
digitalWrite(PIN_OLED_CS, HIGH);
|
|
pinMode(PIN_OLED_CS, OUTPUT);
|
|
pinMode(PIN_USER_BTN, INPUT);
|
|
// Both onboard LEDs are active high. Leave them off until explicitly needed.
|
|
digitalWrite(PA0, LOW);
|
|
pinMode(PA0, OUTPUT);
|
|
digitalWrite(PA1, LOW);
|
|
pinMode(PA1, OUTPUT);
|
|
|
|
SPI.setSCLK(PIN_SPI_SCK);
|
|
SPI.setMISO(PIN_SPI_MISO);
|
|
SPI.setMOSI(PIN_SPI_MOSI);
|
|
SPI.begin();
|
|
delay(200); // OLED power-on settling time used by the manufacturer's example.
|
|
}
|
|
|
|
#ifndef LORA_CR
|
|
#define LORA_CR 5
|
|
#endif
|
|
|
|
static bool check_radio_status(int status, const char* stage) {
|
|
if (status == RADIOLIB_ERR_NONE) return true;
|
|
|
|
Serial.print("ERROR: ");
|
|
Serial.print(stage);
|
|
Serial.print(": ");
|
|
Serial.println(status);
|
|
return false;
|
|
}
|
|
|
|
bool radio_init() {
|
|
radio.setRfSwitchTable(rfswitch_pins, rfswitch_table);
|
|
int status = radio.begin(LORA_FREQ, LORA_BW, LORA_SF, LORA_CR,
|
|
RADIOLIB_SX126X_SYNC_WORD_PRIVATE, LORA_TX_POWER,
|
|
16, STM32WL_TCXO_VOLTAGE, 0);
|
|
if (!check_radio_status(status, "radio.begin")) return false;
|
|
|
|
// Match the manufacturer's 3.3 V power-LDO trim (REG_DRV_CTRL).
|
|
const uint8_t power_ldo_3v3 = 0x0E;
|
|
status = radio.writeRegister(0x091F, &power_ldo_3v3, 1);
|
|
if (!check_radio_status(status, "power LDO trim")) return false;
|
|
|
|
status = radio.setCurrentLimit(SX126X_CURRENT_LIMIT);
|
|
if (!check_radio_status(status, "current limit")) return false;
|
|
status = radio.setRxBoostedGainMode(RX_BOOSTED_GAIN);
|
|
if (!check_radio_status(status, "RX gain")) return false;
|
|
return check_radio_status(radio.setCRC(1), "CRC");
|
|
}
|
|
|
|
mesh::LocalIdentity radio_new_identity() {
|
|
RadioNoiseListener rng(radio);
|
|
return mesh::LocalIdentity(&rng);
|
|
}
|