A cold start can take up to ~30 min with a weak sky view, so the default
limit before the first fix since boot goes from 15 min to 1 h.
The limit is now a GPS preference, set with `gps firstfix <duration>`
(0 = no limit, at most 1 day) and saved with the other GPS settings, so
repeaters and companions can use different values without a rebuild.
GPS_FIRST_FIX_TIMEOUT_MS stays as the build default.
The remote-CLI reply buffers in onPeerDataRecv() (repeater, room server,
sensor) and BaseChatMesh were sized temp[166] for a 5-byte datagram
header plus 161 bytes of reply. But MyMesh::handleCommand() first
reflects a 3-byte correlation prefix (e.g. 'aa|') into the reply, after
which CommonCLI commands may write up to 160 chars + NUL into the
remaining 158 bytes -- overflowing the buffer by 2 bytes (e.g. a full
'regions' listing via exportTo(reply, 160)).
Triggering this remotely crashes the node (observed as an unresponsive
repeater after a prefixed 'regions' query); the 2 out-of-bounds bytes
are a printable region-name character and a NUL.
Size the buffers for the full worst case instead:
5 header + 3 prefix + 160 reply + 1 NUL = 169.
Verified with a host ASan harness reproducing the exact layout:
prefixed 'regions' with a 25-region listing overflowed temp[166]
(BufStream::write, RegionMap.cpp) and now passes clean with temp[169];
unprefixed (serial) path unaffected.
Repeaters, room servers and sensors already let the battery ADC multiplier be tuned with 'set adc.multiplier' (CommonCLI). The companion firmware had no equivalent, so a board whose divider differs from the build default (common on DIY ProMicro / Faketec boards) always reported a wrong battery voltage.
Adds the same command to the companion CLI. The value is stored in the companion prefs (comp.adc_mult, 0 = board default) and applied at startup via MainBoard::setAdcMultiplier().
Move TimeSeriesData from simple_sensor into src/helpers and drive it with
monotonic uptime, so RTC changes cannot stall recording or break queries.
Keep the old RTCClock* overloads as deprecated for custom sensor sketches.
Record 24h of battery, noise floor, TX/RX airtime % and MCU temperature on
repeaters and answer the existing 0x04 min/max/avg request using the same
format as sensor nodes. No packets are sent by this feature.
REPEATER_HISTORY_SLOTS=0 removes it; default off on STM32/RP2040.
Add native tests for TimeSeriesData and document the request and channels.
The room server gated its filesystem paths on NRF52_PLATFORM only, so an
STM32 build fell through to the ESP32 branch and failed to compile:
MyMesh.cpp:147: no matching function for call to
'Adafruit_LittleFS::open(const char*&, const char [2], bool)'
main.cpp:69: 'store' was not declared in this scope
STM32 uses the same InternalFS / Adafruit_LittleFS API as nRF52, including
append semantics (FILE_O_WRITE opens LFS_O_RDWR|LFS_O_CREAT and then seeks
to the end), so the nRF52 branch is already correct for it. Add
STM32_PLATFORM alongside NRF52_PLATFORM in the four remaining gates;
saveIdentity() already did this.
This unblocks the room_server example on the existing STM32WL boards
(wio-e5-mini, wio-e5-dev, rak3x72, tiny_relay) as well as new ones.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Use GxEPD2's busy callback to run the mesh, interface and sensor loops
(loopCore(), shared with loop()) while the panel refreshes, instead of
blocking the main loop. Covers the partial refresh in endFrame(), the
full wipe in startFrame(), and the sleep icon / blank refresh on turnOff().