Commit Graph
3341 Commits
Author SHA1 Message Date
agessaman 974564b89c feat(rak3401): cold-sleep RAK4631 onboard SX1262 on RAK13302 builds
A RAK4631 core paired with a RAK13302 leaves the core's own SX1262
powered but never initialized, idling in STDBY_RC for the life of the
board. Firmware cannot cut its supply -- P1.05 is the RF switch rail,
not the radio's -- so bring it up on its own pins just long enough to
issue a cold sleep, before std_init() repins SPI onto the RAK13302.

Gated behind RAK4631_ONBOARD_SX1262_SLEEP and exposed through seven
RAK_4631_13302_* envs, so RAK_3401_* artifacts are unchanged.

The sleep is issued regardless of what begin() returns: Module::init()
runs first, so SPI stays usable even if TCXO calibration fails. NSS is
then held high, since the SX1262 wakes on an NSS falling edge.

Verified on RAK19007 + RAK4631 + RAK13302: begin=0 sleep=0, RAK13302
init clean (device_errors=0x0000), TX and RX both confirmed. The
current saving itself is derived from the datasheet (600 uA STDBY_RC
-> 160 nA cold sleep) and is not measured.
2026-08-17 21:04:06 -07:00
Huw Duddy 22bc13804c Merge pull request #3218 from fkallay1/fix/lr2021-set-tx-power-rx-stall
Fix LR2021 occasionally stopping reception after a TX power change
2026-08-17 23:20:32 +10:00
Huw Duddy debbbb81c0 trimmed comment 2026-08-17 23:16:01 +10:00
Fedor Kallay aa2292459f fix(lr2021): setTxPower() could leave the receiver down until reboot
RadioLibWrapper::setTxPower() called setOutputPower() and nothing else. On
LR2021 that writes the PA config and TxParams, which are standby-only commands,
and it never re-arms the receiver.

This only affects LR2021 boards. recvRaw() has:

    #if defined(USE_LR2021)
      state = STATE_RX;    // LR2021 stays in Rx after readData
    #else
      state = STATE_IDLE;  // need another startReceive()
    #endif

so on SX126x the next recvRaw() re-arms Rx anyway and the write is harmless,
while on LR2021 startReceive() is never called again on its own. A 'set tx'
issued while the radio was listening could therefore stop reception until the
next reboot. Observed a few times on an LR2021 repeater; recovery required a
power cycle.

Dispatcher's stuck-radio check does not catch it: isInRecvMode() reports the
wrapper's own `state` flag rather than the chip's actual mode, so it still
believes the radio is in Rx, and it only raises ERR_EVENT_STARTRX_TIMEOUT
without attempting recovery.

Fix: on LR2021, drop to standby via idle() before writing the PA config and let
checkRecv() re-arm Rx - the same pattern resetAGC() and
applySideDetectorConfig() already use. Other radios are left untouched.

Affects meshtracker_x1 and meshnology_w12 (both USE_LR2021).

Tested on hardware with an LR2021 repeater: six consecutive 'set tx' changes
(15/18/21/14/19/14), after which the radio kept receiving and forwarding
traffic (rawrx/rxpkts increasing, no missed IRQs). Noise-floor sampling also
kept updating, which only happens while state == STATE_RX.
2026-08-15 02:31:19 +02:00
Scott Powell cad602e416 * version 1.17.1 companion-v1.17.1 repeater-v1.17.1 room-server-v1.17.1 2026-08-14 22:19:19 +10:00
Huw Duddy 54040eef43 Merge pull request #3206 from meshcore-dev/nrf-combine-rng-entropy
combine radio's entropy with CC310 RNG
2026-08-14 22:09:26 +10:00
Scott Powell 10b6552872 * combine radio's entropy with CC310 RNG 2026-08-14 17:46:43 +10:00
Huw Duddy 0523076479 Merge pull request #3203 from meshcore-dev/companion-fem-pref-fix
commenting out the load/save of the fem_ properties
2026-08-14 16:44:59 +10:00
Scott Powell c97e40d15d * unit test no longer valid 2026-08-14 16:42:54 +10:00
Scott Powell 5ff2d7109b * commenting out the load/save of the fem_ properties, until they can be set 2026-08-14 16:30:12 +10:00
ripplebiz f8832af086 Merge pull request #3106 from ViezeVingertjes/fix/scoped-reply-routing
Fix replies dropped when flood.max.unscoped is low
2026-08-13 15:00:37 +10:00
ripplebiz 2581baaaa4 Merge pull request #3189 from oltaco/nrf52-unused-pin-sweep
Fix unused pin definitions on some NRF52 boards
2026-08-13 13:48:59 +10:00
taco a80ddbf4e2 Fix LilyGo T-Echo Lite SPI pins 2026-08-13 00:53:58 +10:00
taco d0ceba7976 Fix Heltec MeshPocket SPI pins 2026-08-13 00:15:34 +10:00
taco 0028bd9bec Fix Heltec T1 pin definitions
SPI pins that are set to -1 cause OOB reads on NRF52. The unused Serial2 pin definitions were removed to avoid potential issues with the Uart framework.
2026-08-13 00:12:37 +10:00
ripplebiz 09933264fb Merge pull request #3188 from oltaco/heltec-t096-pin-fix
Fix Heltec T096 Tx issue
2026-08-12 23:00:31 +10:00
taco 248e6a9fab Heltec T096: fix PIN_SPI1_MISO
Setting SPI pins to values that are OOB of the g_ADigitalPinMap[] array causes OOB reads. This variant.h has pin 0 as 0xFF which passes through as NRFX_SPIM_PIN_NOT_USED.
2026-08-12 22:31:57 +10:00
taco 0f686aa3f1 Revert "t096 compiler layout workaround"
This reverts commit bdefc8d085.
2026-08-12 22:28:36 +10:00
taco 920ee315ec Revert "T096 PA_CTX pin direction workaround"
This reverts commit b13962d7de.
2026-08-12 22:28:05 +10:00
ripplebiz 6b79020bbd Merge pull request #3185 from oltaco/fix-techo-card-txco-voltage
Set T-Echo Card TCXO voltage to 3.0
2026-08-12 18:13:44 +10:00
ripplebiz d5949f93d8 Merge pull request #3137 from agessaman/feat/station-g3-fem-prefs
Station G3: Expose, persist, and apply FEM gain preferences
2026-08-12 16:11:23 +10:00
taco 309a04162e set T-Echo Card TCXO voltage to 3.0
as per https://github.com/meshcore-dev/MeshCore/pull/3140 and https://github.com/Xinyuan-LilyGO/T-Echo-Lite/issues/14
2026-08-12 16:08:05 +10:00
ripplebiz c913b0fec1 Merge pull request #3182 from oltaco/t096-tx-workaround
Workaround for Heltec T096 transmit issue
2026-08-12 14:49:32 +10:00
taco b13962d7de T096 PA_CTX pin direction workaround 2026-08-12 14:07:31 +10:00
taco bdefc8d085 t096 compiler layout workaround
see https://github.com/meshcore-dev/MeshCore/issues/3151
2026-08-12 14:04:50 +10:00
ripplebiz 3dfbcf93b8 Merge pull request #3154 from fdlamotte/nrf52_hwcrypto_init
nrf52: call nRFCrypto.begin()/end() only once
2026-08-12 12:14:21 +10:00
Huw Duddy 467fe37109 Merge pull request #3170 from recrof/promicro-pin-tidy-up
[promicro] make pinmap more tidy, move the LoRa pins to variant.h
2026-08-11 18:43:20 +10:00
Rastislav Vysoky 3631de37de removed misleading 'GPIO' from pin numbers 2026-08-11 10:37:20 +02:00
ripplebiz c6d2dd6234 Merge pull request #3164 from weebl2000/fix-tbeam-s3-display
Fix display issues on T-beam Supreme S3
2026-08-11 14:39:39 +10:00
agessaman f82950f311 feat(companion_radio): add external FEM gain preferences for RX and TX for companions
Introduced consistent preferences for external LoRa FEM RX and TX gain settings in NodePrefs. Updated companion MyMesh to apply these settings during initialization and transmission. Added unit tests to verify the round-trip serialization of these new preferences.
2026-08-10 11:59:26 -07:00
Rastislav Vysoky a3825aa272 make promicro pinmap more tidy, move the LoRa pins to variant.h 2026-08-10 20:13:59 +02:00
Liam Cottle ff0ef14159 Merge pull request #3166 from recrof/debug-noise-floor-flag
move RadioLibWrapper noise_floor level message under special debug flag
2026-08-11 03:07:31 +12:00
Rastislav Vysoky 09ef746f29 move RadioLibWrapper noise_floor level message under special debug flag 2026-08-10 16:56:56 +02:00
Wessel Nieboer 1d98c49b1b Fix T-beam Supreme S3 display 2026-08-10 13:39:16 +02:00
Huw Duddy 5f55d855bc Merge pull request #3158 from mepholic/bug/fix-rxgain-setting-post-agc-reset
Fix RX Boosted Gain setting after AGC reset is triggered
2026-08-10 17:31:38 +10:00
ripplebiz 04fda41bd5 Merge pull request #3142 from oltaco/buildfix-userbtn
Build fix for R1 Neo and Minewsemi repeater
2026-08-10 13:30:24 +10:00
ripplebiz 0d743ba144 Merge pull request #3146 from oltaco/lr2021-preamble-and-irq-timeout
LR2021: add PREAMBLE_DETECTED bit and IRQ timeout logic
2026-08-10 13:29:12 +10:00
Dan Theisen 397ea610e6 RX Boosted Gain was set back to the compiled in value rather than the current/flash value set by the user when the ACG reset is triggered. This commit fixes this. 2026-08-09 18:11:35 -07:00
Florent b8324f4fa8 nrf52: call nRFCrypto.begin()/end() only once 2026-08-09 14:46:23 -04:00
Huw Duddy 79d2eeaa76 Merge pull request #3148 from recrof/add-missing-kiss-radio
add missing kiss radio roles, add kiss radio build to build.sh
2026-08-09 22:22:08 +10:00
Rastislav Vysoky d3f9cbb922 add missing kiss radio roles, add kiss radio build to build.sh 2026-08-09 14:17:18 +02:00
Huw Duddy 66eb74f0fb Merge pull request #3140 from entr0p1/fix/techo-lite-pins
Lilygo T-Echo Lite Pin Fixes
2026-08-09 22:06:21 +10:00
taco 203c44c9f5 LR2021: add PREAMBLE_DETECTED bit and IRQ timeout logic 2026-08-09 21:41:22 +10:00
taco 2d412be465 minewsemi: build fix and platformio.ini tidy up
fixes minewsemi repeater failing build due to user_btn missing.
2026-08-09 18:33:27 +10:00
taco 05bdabe425 R1 neo: remove stray lib_deps entry 2026-08-09 16:51:45 +10:00
taco 7634c077e5 build fix for R1 Neo repeater
added missing declarations for user_btn and NullDisplayDriver
2026-08-09 16:50:44 +10:00
Scott Powell da1fc9c0e8 Merge branch 'dev'
# Conflicts:
#	docs/payloads.md
companion-v1.17.0 repeater-v1.17.0 room-server-v1.17.0
2026-08-09 15:16:48 +10:00
Scott Powell 68dedd3e96 * version 1.17.0 2026-08-09 15:14:46 +10:00
entr0p1 430ef3b086 Lilygo T-Echo Lite Pin Fixes
- Aligned to Lilygo's updated schematic and pin map as per https://github.com/Xinyuan-LilyGO/T-Echo-Lite/issues/14
2026-08-09 14:09:35 +10:00
ripplebiz 02f7fb7cbc Merge pull request #3139 from oltaco/x1-flash
Add QSPIFlash support for Seeed MeshTracker X1
2026-08-09 13:52:56 +10:00