Commit Graph
1182 Commits
Author SHA1 Message Date
Thomas Osterried cedc9977c2 Skip empty channel slots in searchChannelsByHash
An unconfigured slot has an all-zero secret, so it matches null-key group traffic (a sender with an unset PSK). The zero-key MAC validates against the empty slot and the foreign message is delivered as if it belonged to that channel — every node with a free slot is a null-key sink. Skip empty slots.
2026-08-19 09:35:25 +02:00
ripplebiz 6d8f16fabb Merge pull request #3246 from liamcottle/update/toolchain
Update GCC toolchain for nRF52 boards to fix builds on Raspberry Pi
2026-08-19 11:30:08 +10:00
liamcottle deb5e735b8 updated gcc toolchain for nrf52 boards 2026-08-19 12:07:29 +12:00
fdlamotte ed227b9cb6 Merge pull request #3180 from fdlamotte/thinknode_m8
thinknode_m8: initial support

adds some functionalities to ui_task and epddisplay:

epd display, 
- supports screen off, and clear screen
- supports forcing full refresh every N partial refreshes (off by default, configured to 60 for M8)

ui_task
- UI_SHOW_CLOCK flag to display clock on first screen
- rotary button can act like joystick (with regards to Enter key), defaults to old config for existing nodes
- screen off on long press when using rotary button (very handy for the watch)
2026-08-18 09:33:42 -04:00
Rastislav Vysoky 053fa3eb83 fix: move MeshadventurerBoard.h to correct location 2026-08-18 13:51:55 +02:00
Florent cec44c05dd gxepd: do full refresh before screen off ... so wakes quicker ;) 2026-08-17 09:41:51 -04:00
Huw Duddy debbbb81c0 trimmed comment 2026-08-17 23:16:01 +10:00
Florent 3f4be26003 gxepddisplay: better handling of full refresh (no faint partial afterwards !!!) 2026-08-16 11:40:13 -04:00
Fedor Kallay aa2292459f fix(lr2021): setTxPower() could leave the receiver down until reboot
RadioLibWrapper::setTxPower() called setOutputPower() and nothing else. On
LR2021 that writes the PA config and TxParams, which are standby-only commands,
and it never re-arms the receiver.

This only affects LR2021 boards. recvRaw() has:

    #if defined(USE_LR2021)
      state = STATE_RX;    // LR2021 stays in Rx after readData
    #else
      state = STATE_IDLE;  // need another startReceive()
    #endif

so on SX126x the next recvRaw() re-arms Rx anyway and the write is harmless,
while on LR2021 startReceive() is never called again on its own. A 'set tx'
issued while the radio was listening could therefore stop reception until the
next reboot. Observed a few times on an LR2021 repeater; recovery required a
power cycle.

Dispatcher's stuck-radio check does not catch it: isInRecvMode() reports the
wrapper's own `state` flag rather than the chip's actual mode, so it still
believes the radio is in Rx, and it only raises ERR_EVENT_STARTRX_TIMEOUT
without attempting recovery.

Fix: on LR2021, drop to standby via idle() before writing the PA config and let
checkRecv() re-arm Rx - the same pattern resetAGC() and
applySideDetectorConfig() already use. Other radios are left untouched.

Affects meshtracker_x1 and meshnology_w12 (both USE_LR2021).

Tested on hardware with an LR2021 repeater: six consecutive 'set tx' changes
(15/18/21/14/19/14), after which the radio kept receiving and forwarding
traffic (rawrx/rxpkts increasing, no missed IRQs). Noise-floor sampling also
kept updating, which only happens while state == STATE_RX.
2026-08-15 02:31:19 +02:00
Scott Powell 10b6552872 * combine radio's entropy with CC310 RNG 2026-08-14 17:46:43 +10:00
ripplebiz f8832af086 Merge pull request #3106 from ViezeVingertjes/fix/scoped-reply-routing
Fix replies dropped when flood.max.unscoped is low
2026-08-13 15:00:37 +10:00
ripplebiz 09933264fb Merge pull request #3188 from oltaco/heltec-t096-pin-fix
Fix Heltec T096 Tx issue
2026-08-12 23:00:31 +10:00
taco 0f686aa3f1 Revert "t096 compiler layout workaround"
This reverts commit bdefc8d085.
2026-08-12 22:28:36 +10:00
ripplebiz d5949f93d8 Merge pull request #3137 from agessaman/feat/station-g3-fem-prefs
Station G3: Expose, persist, and apply FEM gain preferences
2026-08-12 16:11:23 +10:00
ripplebiz c913b0fec1 Merge pull request #3182 from oltaco/t096-tx-workaround
Workaround for Heltec T096 transmit issue
2026-08-12 14:49:32 +10:00
taco bdefc8d085 t096 compiler layout workaround
see https://github.com/meshcore-dev/MeshCore/issues/3151
2026-08-12 14:04:50 +10:00
ripplebiz 3dfbcf93b8 Merge pull request #3154 from fdlamotte/nrf52_hwcrypto_init
nrf52: call nRFCrypto.begin()/end() only once
2026-08-12 12:14:21 +10:00
Florent 109ed685b2 thinknode_m8: initial support 2026-08-11 17:37:35 -04:00
ripplebiz c6d2dd6234 Merge pull request #3164 from weebl2000/fix-tbeam-s3-display
Fix display issues on T-beam Supreme S3
2026-08-11 14:39:39 +10:00
agessaman f82950f311 feat(companion_radio): add external FEM gain preferences for RX and TX for companions
Introduced consistent preferences for external LoRa FEM RX and TX gain settings in NodePrefs. Updated companion MyMesh to apply these settings during initialization and transmission. Added unit tests to verify the round-trip serialization of these new preferences.
2026-08-10 11:59:26 -07:00
Rastislav Vysoky 09ef746f29 move RadioLibWrapper noise_floor level message under special debug flag 2026-08-10 16:56:56 +02:00
Wessel Nieboer 1d98c49b1b Fix T-beam Supreme S3 display 2026-08-10 13:39:16 +02:00
Huw Duddy 5f55d855bc Merge pull request #3158 from mepholic/bug/fix-rxgain-setting-post-agc-reset
Fix RX Boosted Gain setting after AGC reset is triggered
2026-08-10 17:31:38 +10:00
Dan Theisen 397ea610e6 RX Boosted Gain was set back to the compiled in value rather than the current/flash value set by the user when the ACG reset is triggered. This commit fixes this. 2026-08-09 18:11:35 -07:00
Florent b8324f4fa8 nrf52: call nRFCrypto.begin()/end() only once 2026-08-09 14:46:23 -04:00
taco 203c44c9f5 LR2021: add PREAMBLE_DETECTED bit and IRQ timeout logic 2026-08-09 21:41:22 +10:00
agessaman 2eb7feffe0 fix(station-g3): expose FEM gain preferences 2026-08-06 15:29:14 -07:00
Hacuchino-hash f8ea866b1f Add RGB LED and haptic notifications for SenseCAP MeshTracker X1 2026-08-06 07:27:05 -05:00
ripplebiz 8bf182fb41 Merge pull request #3115 from oltaco/meshnology_w12
Add support for Meshnology W12 and LR2021 Wrapper
2026-08-05 15:04:00 +10:00
taco cb7b158931 LR2021: auto-LDRO for side detectors 2026-08-05 14:23:32 +10:00
taco c2b7e56cbc LR2021: fix for hardware cad and side detectors 2026-08-05 14:23:32 +10:00
taco 5687ba3f87 LR2021 multi-SF support (side detectors) 2026-08-05 14:23:32 +10:00
taco e2d050df9f add Meshnology W12 support and LR2021 wrapper 2026-08-05 14:23:29 +10:00
ViezeVingertjes 4820f0916d Merge remote-tracking branch 'upstream/dev' into fix/scoped-reply-routing
# Conflicts:
#	examples/simple_repeater/MyMesh.cpp
2026-08-04 11:49:58 +02:00
ViezeVingertjes 34156ddb11 Fix replies dropped when flood.max.unscoped is low 2026-08-03 22:57:12 +02:00
Huw Duddy 06685f6fae Merge pull request #3076 from MDamon/fix/lr1110-rx-timeout
LR1110: fix startReceive() passing an IRQ bit as the RX timeout 🤖🤖
2026-08-03 23:02:52 +10:00
Huw Duddy 02bb3bbad8 Clean up comments in startReceive method
Removed unnecessary comments regarding RX timeout and IRQ mask.
2026-08-03 22:57:34 +10:00
ripplebiz 1b4afa95b6 Merge pull request #2824 from NickDunklee/rak-advert-hw-encryption
feat: use nrf52 hardware crypto where we can
2026-08-02 15:35:33 +10:00
Mike Damon d535134724 LR1110: fix startReceive() passing an IRQ bit as the RX timeout
CustomLR1110::startReceive() passed RADIOLIB_LR11X0_IRQ_PREAMBLE_DETECTED
(1<<4 = 16) as RadioLib's first argument, which is the RX *timeout*, not an
IRQ mask. At the LR11x0's 30.52us tick that armed the receiver for ~488us, so
it dropped out of RX before any packet could arrive and the node received
nothing at all -- while transmitting normally.

Symptoms on a SenseCAP T1000-E: tx_air_secs rising, rx_air_secs stuck at 0,
recv_errors 0, and the noise floor pinned at the -120 clamp because
getCurrentRSSI() never sampled a live receiver.

Pass RADIOLIB_LR11X0_RX_TIMEOUT_INF (continuous RX), which is what
LR11x0::startReceive() itself uses, keeping the PREAMBLE_DETECTED flag in the
reported IRQ flags as intended.

Introduced in 04b643b2 ("LR1110: add PREAMBLE_DETECTED to reported irq flags").
Verified on two T1000-E units: with only the repeater fixed it began receiving
(last_rssi -29, SNR 17.0) while the unfixed companion stayed deaf; fixing both
brought up the link in each direction.
2026-07-30 12:14:39 -04:00
ripplebiz 837869fa93 Merge pull request #3004 from axhoff/agent/preserve-utf8-advert-names
Preserve UTF-8 boundaries in advert names
2026-07-30 12:59:59 +10:00
ripplebiz ef08c7b0f3 Merge pull request #3063 from oltaco/unify-irq-timeout
Unify IRQ timeout logic across all applicable radio types
2026-07-29 23:52:48 +10:00
ripplebiz 4cf508121e Merge pull request #3049 from liamcottle/feature/ethernet
Refactor Companion Interfaces + Add ThinkNode M7 Ethernet Support
2026-07-29 23:45:51 +10:00
taco dc6264b870 LLCC68: add IRQ timeout logic 2026-07-29 23:34:01 +10:00
taco 2f19204283 SX1268: add IRQ timeout logic 2026-07-29 23:34:01 +10:00
taco c490abf452 STM32WLx: add IRQ timeout logic 2026-07-29 23:33:51 +10:00
taco 7fbac66a33 LR1110: fix unnecessary IRQ clear 2026-07-29 23:18:15 +10:00
ripplebiz 12476c3684 Merge pull request #3062 from oltaco/fix-irq-clear
Fix unnecessary IRQ clearing
2026-07-29 22:37:30 +10:00
taco 0f543ccc34 fix unnecessary IRQ clear 2026-07-29 21:39:56 +10:00
entr0p1 d4ee0fc4eb nRF52840 "start ota" Failure Recovery
If Bluefruit.begin fails, BLE OTA mode won't actually start and the board might require a reboot to reattempt.

Fixes:
- Bluefruit.begin returns false in NRF52Board.startOTAUpdate if OTA mode fails to start. User is notified of the fault through existing error message in CommonCLI and can reattempt "start ota" command.
2026-07-28 10:14:59 +10:00
liamcottle 4ba459402c remove old rak ethernet interface 2026-07-28 03:18:54 +12:00