Measured 7. 8. 2026: bench-board had been running 811 days behind since it was deployed, and every board on the bench was 812 days behind. Nobody had ever set their clocks, because setting one was a manual step documented in two places and performed in neither. That is not cosmetic. Mesh.cpp stamps every advert a node transmits from the RTC, and a receiver drops a stale timestamp as a replay -- so a wrong clock turns into replies that vanish. Nothing could fix it by itself. The only automatic sources in the tree are GPS (which these nodes do not have) and BaseChatMesh, which the repeater build does not link; and `clock sync` cannot work from the console at all, because USB and BLE share one command buffer and pass sender_timestamp = 0, so the `sender_timestamp > curr` guard is never satisfied. So build_version.py now also stamps FIRMWARE_BUILD_EPOCH, and that -- not a hardcoded 15 May 2024 -- is where a clock with no other source comes up. A freshly flashed board is right to within "time since compile". It needs no GPS, nothing carrying a correct time on air, and no host: the one case the host-side tooling cannot reach. Verified on x1: build epoch 1786100869 = 11:07:49, and after a reboot the board came up at 11:07:47. The #ifndef fallback is load-bearing, not decoration: build_version.py is nRF52-only and reaches 7 of the 16 local envs, so upstream envs never define it. Verifying an integer define is not `strings` -- dump .text and look for the word, and check the old literal is gone from all three sites. `clock` also reports the epoch now. Its human part is minutes only, so a host comparing clocks could not see a difference under a minute and had to leave a 59 s deadband; appended, so anything that just prints the reply is unaffected. Also here, and DISABLED, is carrying the clock across a soft reset in retained RAM. It was tried and measured not to work: the record at 0x2003FFE0 came back as `00000000 10001000 00000000` after a reboot -- not zeroed, OVERWRITTEN, and 0x10001000 is the nRF52 UICR base, i.e. a UICR pointer left on the Adafruit bootloader's stack. The bootloader runs before the app on every reset and links against the full RAM, so it owns the top of it; being outside the app's linker region is not enough. The code stays because it self-disables against __StackTop and now says so at boot, and because the same doubt applies to the hardfault record at 0x2003FFF0, which sits HIGHER -- treat a missing hardfault report as "unknown", not as "nothing crashed". Two things that cost a cycle each and are now designed out: the restore's "nothing stored" branch was silent, which is indistinguishable from "working"; and `clkreboot` would have undone itself, writing the build epoch and then having the reboot restore the value it just discarded (weak retainedClockInvalidate() closes that). Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
About MeshCore
MeshCore is a lightweight, portable C++ library that enables multi-hop packet routing for embedded projects using LoRa and other packet radios. It is designed for developers who want to create resilient, decentralized communication networks that work without the internet.
🔍 What is MeshCore?
MeshCore now supports a range of LoRa devices, allowing for easy flashing without the need to compile firmware manually. Users can flash a pre-built binary using tools like Adafruit ESPTool and interact with the network through a serial console. MeshCore provides the ability to create wireless mesh networks, similar to Meshtastic and Reticulum but with a focus on lightweight multi-hop packet routing for embedded projects. Unlike Meshtastic, which is tailored for casual LoRa communication, or Reticulum, which offers advanced networking, MeshCore balances simplicity with scalability, making it ideal for custom embedded solutions, where devices (nodes) can communicate over long distances by relaying messages through intermediate nodes. This is especially useful in off-grid, emergency, or tactical situations where traditional communication infrastructure is unavailable.
⚡ Key Features
- Multi-Hop Packet Routing
- Devices can forward messages across multiple nodes, extending range beyond a single radio's reach.
- Supports up to a configurable number of hops to balance network efficiency and prevent excessive traffic.
- Nodes use fixed roles where "Companion" nodes are not repeating messages at all to prevent adverse routing paths from being used.
- Supports LoRa Radios – Works with Heltec, RAK Wireless, and other LoRa-based hardware.
- Decentralized & Resilient – No central server or internet required; the network is self-healing.
- Low Power Consumption – Ideal for battery-powered or solar-powered devices.
- Simple to Deploy – Pre-built example applications make it easy to get started.
🎯 What Can You Use MeshCore For?
- Off-Grid Communication: Stay connected even in remote areas.
- Emergency Response & Disaster Recovery: Set up instant networks where infrastructure is down.
- Outdoor Activities: Hiking, camping, and adventure racing communication.
- Tactical & Security Applications: Military, law enforcement, and private security use cases.
- IoT & Sensor Networks: Collect data from remote sensors and relay it back to a central location.
🚀 How to Get Started
- Watch the MeshCore QuickStart Playlist by The Comms Channel
- Watch the MeshCore Technical Presentation by Liam Cottle.
- Read through our Frequently Asked Questions and Documentation.
- Flash the MeshCore firmware on a supported device.
- Connect with a supported client.
For developers:
- Install PlatformIO in Visual Studio Code.
- Clone and open the MeshCore repository in Visual Studio Code.
- See the example applications you can modify and run:
- Companion Radio - For use with an external chat app, over BLE, USB or Wi-Fi.
- KISS Modem - Serial KISS protocol bridge for host applications. (protocol docs)
- Simple Repeater - Extends network coverage by relaying messages.
- Simple Room Server - A simple BBS server for shared Posts.
- Simple Secure Chat - Secure terminal based text communication between devices.
- Simple Sensor - Remote sensor node with telemetry and alerting.
The Simple Secure Chat example can be interacted with through the Serial Monitor in Visual Studio Code, or with a Serial USB Terminal on Android.
⚡️ MeshCore Flasher
We have prebuilt firmware ready to flash on supported devices.
- Launch https://meshcore.io/flasher
- Select a supported device
- Flash one of the firmware types:
- Companion, Repeater or Room Server
- Once flashing is complete, you can connect with one of the MeshCore clients below.
📱 MeshCore Clients
Companion Firmware
The companion firmware can be connected to via BLE, USB or Wi-Fi depending on the firmware type you flashed.
- Web: https://app.meshcore.nz
- Android: https://play.google.com/store/apps/details?id=com.liamcottle.meshcore.android
- iOS: https://apps.apple.com/us/app/meshcore/id6742354151?platform=iphone
- NodeJS: https://github.com/liamcottle/meshcore.js
- Python: https://github.com/fdlamotte/meshcore-cli
Repeater and Room Server Firmware
The repeater and room server firmware can be set up via USB in the web config tool.
They can also be managed via LoRa in the mobile app by using the Remote Management feature.
🛠 Hardware Compatibility
MeshCore is designed for devices listed in the MeshCore Flasher
📜 License
MeshCore is open-source software released under the MIT License. You are free to use, modify, and distribute it for personal and commercial projects.
Contributing
Please submit PR's using 'dev' as the base branch! For minor changes just submit your PR and we'll try to review it, but for anything more 'impactful' please open an Issue first and start a discussion. It is better to sound out what it is you want to achieve first, and try to come to a consensus on what the best approach is, especially when it impacts the structure or architecture of this codebase.
Here are some general principles you should try to adhere to:
- Keep it simple. Please, don't think like a high-level lang programmer. Think embedded, and keep code concise, without any unnecessary layers.
- No dynamic memory allocation, except during setup/begin functions.
- Use the same brace and indenting style that's in the core source modules. (A .clang-format is probably going to be added soon, but please do NOT retroactively re-format existing code. This just creates unnecessary diffs that make finding problems harder)
Help us prioritize! Please react with thumbs-up to issues/PRs you care about most. We look at reaction counts when planning work.
Running unit tests
To run unit tests, run the following command:
pio test --environment native --verbose
Road-Map / To-Do
There are a number of fairly major features in the pipeline, with no particular time-frames attached yet. In very rough chronological order:
- Companion radio: UI redesign
- Repeater + Room Server: add ACL's (like Sensor Node has)
- Standardise Bridge mode for repeaters
- Repeater/Bridge: Standardise the Transport Codes for zoning/filtering
- Core + Repeater: enhanced zero-hop neighbour discovery
- Core: round-trip manual path support
- Companion + Apps: support for multiple sub-meshes (and 'off-grid' client repeat mode)
- Core + Apps: support for LZW message compression
- Core: dynamic CR (Coding Rate) for weak vs strong hops
- Core: new framework for hosting multiple virtual nodes on one physical device
- V2 protocol spec: discussion and consensus around V2 packet protocol, including path hashes, new encryption specs, etc
📞 Get Support
- Report bugs and request features on the GitHub Issues page.
- Find additional guides and components on my site.
- Join MeshCore Discord to chat with the developers and get help from the community.