tthandClaude Opus 5 59e974854f feat(repeater): blink on|off, txpwr with RadioLib's verdict; UF2 flash helper
blink: a fixed burst is a race against walking to the bench -- 30 blinks
(~7 s) was not enough to find the board in time. `blink on` now runs until
`blink off`, with a 10-minute backstop so a node left blinking does not
quietly eat a battery. Cap on the counted form raised to 999.

txpwr: `set tx` cannot tell you whether the radio took the value. It clamps
to -9..30, saves the pref and replies "OK", but SX1262 accepts only -9..+22
and rejects the rest WITHOUT touching the PA -- so `get tx` can report a
power the radio never had. An earlier sweep here measured +2 dBm and -9 dBm
as RSSI -44.1 and -44.0 at a witness and concluded runtime tx power "does
not work"; that conclusion rested on an instrument that could not
distinguish a refused request from a link that does not care.
RadioLibWrapper::setTxPower keeps the status now (the signature stays void,
it implements an upstream callback), and `txpwr [dBm]` reports it. It
deliberately does not write the pref, so a sweep cannot leave a node booting
at some experimental power.

xiao_uf2_flash.sh: the 1200-baud touch is roughly a coin flip on this build.
Today it worked twice, then wedged x4, then wedged x1 -- and a wedged board
is gone from USB *and* BLE, does not recover on its own (waited 400 s) and
needs a physical replug. Not a "too soon after boot" effect: x1 had been up
23 minutes. Double-tap RESET into UF2 is reliable and takes seconds, so this
makes that the easy path. It refuses to act when several UF2 drives are
present rather than guessing, since they are all labelled XIAO-SENSE.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
2026-08-04 12:45:28 +02:00
2026-04-28 21:39:34 +10:00
2025-01-13 14:07:48 +11:00
2025-06-05 20:35:40 +12:00
2026-04-24 19:37:21 +00:00
2026-02-03 13:47:43 +13:00
2026-03-23 14:26:56 +01:00
2025-01-20 10:20:42 +11:00
2025-01-25 23:09:09 +11:00
2026-03-31 00:51:15 +13:00
2026-06-06 21:12:43 +10:00
2025-03-03 18:08:00 +13:00
2026-06-05 21:25:25 +12:00

About MeshCore

MeshCore is a lightweight, portable C++ library that enables multi-hop packet routing for embedded projects using LoRa and other packet radios. It is designed for developers who want to create resilient, decentralized communication networks that work without the internet.

🔍 What is MeshCore?

MeshCore now supports a range of LoRa devices, allowing for easy flashing without the need to compile firmware manually. Users can flash a pre-built binary using tools like Adafruit ESPTool and interact with the network through a serial console. MeshCore provides the ability to create wireless mesh networks, similar to Meshtastic and Reticulum but with a focus on lightweight multi-hop packet routing for embedded projects. Unlike Meshtastic, which is tailored for casual LoRa communication, or Reticulum, which offers advanced networking, MeshCore balances simplicity with scalability, making it ideal for custom embedded solutions, where devices (nodes) can communicate over long distances by relaying messages through intermediate nodes. This is especially useful in off-grid, emergency, or tactical situations where traditional communication infrastructure is unavailable.

⚡ Key Features

  • Multi-Hop Packet Routing
    • Devices can forward messages across multiple nodes, extending range beyond a single radio's reach.
    • Supports up to a configurable number of hops to balance network efficiency and prevent excessive traffic.
    • Nodes use fixed roles where "Companion" nodes are not repeating messages at all to prevent adverse routing paths from being used.
  • Supports LoRa Radios – Works with Heltec, RAK Wireless, and other LoRa-based hardware.
  • Decentralized & Resilient – No central server or internet required; the network is self-healing.
  • Low Power Consumption – Ideal for battery-powered or solar-powered devices.
  • Simple to Deploy – Pre-built example applications make it easy to get started.

🎯 What Can You Use MeshCore For?

  • Off-Grid Communication: Stay connected even in remote areas.
  • Emergency Response & Disaster Recovery: Set up instant networks where infrastructure is down.
  • Outdoor Activities: Hiking, camping, and adventure racing communication.
  • Tactical & Security Applications: Military, law enforcement, and private security use cases.
  • IoT & Sensor Networks: Collect data from remote sensors and relay it back to a central location.

🚀 How to Get Started

For developers:

The Simple Secure Chat example can be interacted with through the Serial Monitor in Visual Studio Code, or with a Serial USB Terminal on Android.

⚡️ MeshCore Flasher

We have prebuilt firmware ready to flash on supported devices.

  • Launch https://meshcore.io/flasher
  • Select a supported device
  • Flash one of the firmware types:
    • Companion, Repeater or Room Server
  • Once flashing is complete, you can connect with one of the MeshCore clients below.

📱 MeshCore Clients

Companion Firmware

The companion firmware can be connected to via BLE, USB or Wi-Fi depending on the firmware type you flashed.

Repeater and Room Server Firmware

The repeater and room server firmware can be set up via USB in the web config tool.

They can also be managed via LoRa in the mobile app by using the Remote Management feature.

🛠 Hardware Compatibility

MeshCore is designed for devices listed in the MeshCore Flasher

📜 License

MeshCore is open-source software released under the MIT License. You are free to use, modify, and distribute it for personal and commercial projects.

Contributing

Please submit PR's using 'dev' as the base branch! For minor changes just submit your PR and we'll try to review it, but for anything more 'impactful' please open an Issue first and start a discussion. It is better to sound out what it is you want to achieve first, and try to come to a consensus on what the best approach is, especially when it impacts the structure or architecture of this codebase.

Here are some general principles you should try to adhere to:

  • Keep it simple. Please, don't think like a high-level lang programmer. Think embedded, and keep code concise, without any unnecessary layers.
  • No dynamic memory allocation, except during setup/begin functions.
  • Use the same brace and indenting style that's in the core source modules. (A .clang-format is probably going to be added soon, but please do NOT retroactively re-format existing code. This just creates unnecessary diffs that make finding problems harder)

Help us prioritize! Please react with thumbs-up to issues/PRs you care about most. We look at reaction counts when planning work.

Running unit tests

To run unit tests, run the following command:

pio test --environment native --verbose

Road-Map / To-Do

There are a number of fairly major features in the pipeline, with no particular time-frames attached yet. In very rough chronological order:

  • Companion radio: UI redesign
  • Repeater + Room Server: add ACL's (like Sensor Node has)
  • Standardise Bridge mode for repeaters
  • Repeater/Bridge: Standardise the Transport Codes for zoning/filtering
  • Core + Repeater: enhanced zero-hop neighbour discovery
  • Core: round-trip manual path support
  • Companion + Apps: support for multiple sub-meshes (and 'off-grid' client repeat mode)
  • Core + Apps: support for LZW message compression
  • Core: dynamic CR (Coding Rate) for weak vs strong hops
  • Core: new framework for hosting multiple virtual nodes on one physical device
  • V2 protocol spec: discussion and consensus around V2 packet protocol, including path hashes, new encryption specs, etc

📞 Get Support

  • Report bugs and request features on the GitHub Issues page.
  • Find additional guides and components on my site.
  • Join MeshCore Discord to chat with the developers and get help from the community.
S
Description
MeshCore fork: repeater antispam (fairness, per-origin advert window, channel filters), analyzer console, BLE console, fixes. Auto-merged with upstream.
Readme MIT
20 MiB
0 Stars 1 Watchers 0 Forks
2026-11-22 06:46:57 +01:00
Languages
C 46.2%
C++ 45.8%
Python 6.1%
Shell 1.5%
OpenSCAD 0.3%
Other 0.1%