4079 Commits
Author SHA1 Message Date
Florent 6b34ae96df gps: Rework the CLI
- more consistency with other cli commands
- new format for gps fix
- gps format accepts postfix (s/m/d/h)
- documentation
2026-11-08 08:47:35 -04:00
Florent 93d165dd8c gps: once command 2026-11-08 08:47:35 -04:00
Florent 539b55b772 gps: move detection into LocationProvider, remove the legacy constructor 2026-11-08 08:47:34 -04:00
Florent d41aee832e gps: guard the clock sync against stalled and too old fixes 2026-11-08 08:47:34 -04:00
Florent a134188c62 gps: serial pin and configuration fixes (nrf52, meshadventurer, tracker_v1, heltec_tracker) 2026-11-08 08:47:34 -04:00
Níckolas Goline bd21096ce0 muzi_base: fix GPS UART pins and re-enable ATGM336H NMEA output
The refactor no longer calls Serial1.setPins() on nRF52, so Serial1 uses
PIN_SERIAL1_RX/TX directly. Those were swapped (the GPS transmits on
P0.20), so no data was received. Fix them and define PIN_GPS_TX/RX by the
gps module's side, as other variants do.

The ATGM336H keeps its NMEA output config across power cycles, and other
firmware may leave every sentence disabled. Re-enable GGA + RMC after each
power-up.
2026-11-08 08:47:34 -04:00
Florent 47959b8960 gps: fix_stats command 2026-11-08 08:47:34 -04:00
Florent 5303703750 gps: adapt ui-new and the sensor managers 2026-11-08 08:47:34 -04:00
Florent a0c5854b59 rak_gps: simplify the rak driver, which now only handles i2c, for nmea use nmea driver directly 2026-11-08 08:47:34 -04:00
Florent e9d197cf79 gps: periodic acquisition rules (timeout, sats and settle time), isEnabled renamed isActive 2026-11-08 08:47:34 -04:00
Florent e58be9ab11 gps: cache the last fix in LocationProvider (isValid vs hasValidFix), fix and status commands 2026-11-08 08:47:34 -04:00
Florent dea38936d7 gps: move the gps CLI to GpsPrefs and convert all targets 2026-11-08 08:47:34 -04:00
Florent 81afafcb35 gps: add GpsDriver, handle the hardware and software switches in the drivers 2026-11-08 08:47:34 -04:00
tthandClaude Opus 5.5 0243af712e simple_repeater: channel bot caps itself at 10 replies per 5 min
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-08 13:29:31 +01:00
Liam Cottle 9f10793f7a Merge pull request #3782 from anders-dc/fix/null-serial-on-boot-overwrite
Fix null _serial dereference when contacts are overwritten during boot
2026-11-09 01:02:31 +13:00
anders-dc 2f00b0e83a fix(companion): guard null _serial in contact overwrite and full callbacks 2026-11-08 11:01:05 +01:00
Liam Cottle 5c40bf745a Merge pull request #3780 from Blake-Latchford/docs/contributing-merge-factors
Incorporate PR Backtesting into CONTRIBUTING.md
2026-11-08 19:06:54 +13:00
Liam Cottle 9ea4b83ed1 Merge pull request #3637 from marcelverdult/upstream-candidate/meshtracker-x1-micronmea-dep
Fix MeshTracker X1 kiss_modem build: inherit MicroNMEA in every environment
2026-11-08 18:38:24 +13:00
tthandClaude Opus 5.5 5f63ba303c Merge upstream/dev (13 commits) [upstream-sync]
pub-release / release (push) Successful in 23m45s
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-08 00:28:06 +01:00
fdlamotte 4b4f1b25ef Merge pull request #3774 from recrof/rpi2350-support
added rp2350 support, harmonized companions with other variants
2026-11-07 15:57:37 -04:00
Blake Latchford 02081ba500 Incorporate PR Backtesting into CONTRIBUTING.md
I used an LLM to review what changes the likelihood of a PR getting merged. I then asked it to select potential changes based on its findings. I selected from those options and carefully guided the LLM to produce several pull requests. I fed the subset of PRs that failed back into the skill and discovered additional missing factors.
2026-11-07 10:31:14 -05:00
ripplebiz 7474e0c036 Merge pull request #3496 from agessaman/feat/kiss-agc-fem-control
KISS modem: AGC, FEM gain and RX boosted gain control
2026-11-07 18:03:40 +11:00
agessaman c0ccb9c7ff Merge remote-tracking branch 'upstream/dev' into feat/kiss-agc-fem-control 2026-11-06 20:38:01 -08:00
Blake LatchfordandClaude Opus 5.5 7d5499e9eb docs: describe stats-core output and its error flags
Document the stats-core output fields and decode the `errors` bitmask
(shown as "Debug flags" in the app), from the ERR_EVENT_* flags in
Dispatcher.h, and note that the flags stay set until reboot or
`clear stats`.

Fixes #3039

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-06 21:19:12 -05:00
Rastislav Vysoky 683680d83b fix: pin to 5.6.0 2026-11-07 00:49:21 +01:00
Rastislav Vysoky c5a0673d67 added rp2350 support, harmonized companions with other variants 2026-11-07 00:35:47 +01:00
Li Hardy Extreme 1e135e0bd2 feat: mDNS ESP32 - enable local network discovery over mDNS 2026-11-06 00:10:59 +01:00
upstream-sync-bot a8518433e2 Merge upstream/dev (2 commits) [upstream-sync]
pub-release / release (push) Successful in 22m54s
2026-11-05 05:06:06 +00:00
Liam Cottle 4343409886 Merge pull request #3099 from jirogit/feat/c6l-kiss-modem
Fix M5Stack Unit C6L kiss_modem env missing USB CDC flags
2026-11-05 07:40:55 +13:00
Will MacGregorandClaude Opus 5 9af19c870c Build nucleo_wl55jc_repeater in PR build check
Adds the new variant to the PR build matrix, next to the existing STM32
entry, so it is covered by CI going forward.

Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
2026-11-04 09:51:33 -05:00
Will MacGregorandClaude Opus 5 afb56bb976 Add variant for ST Nucleo-WL55JC1
Adds repeater, room_server, companion_radio_usb and kiss_modem
environments for the NUCLEO-WL55JC1 (STM32WL55JC, integrated SubGHz radio).

Notes on the board setup:

- Uses the upstream nucleo_wl55jc board. PlatformIO's boards_remap maps it
  to the core's NUCLEO_WL55JC1 variant, so the LEDs, user buttons and the
  LPUART1 -> ST-LINK VCP serial mapping all come from the core rather than
  being redefined here.
- The RF switch table is built from the core's LORAWAN_RFSWITCH_* macros
  (SP3T front end on PC3/PC4/PC5) so it tracks upstream if those are ever
  revised. Both RFO_LP and RFO_HP are registered, so RadioLib selects HP
  above 14 dBm and LP below it.
- board_build.extra_flags pins the device to STM32WL55xx. The stock board
  manifest declares product_line STM32WL55xx but extra_flags -DSTM32WLE5xx;
  that only works because every #elif chain happens to test WL55xx first.
- The Nucleo's LD1..LD3 are driven active HIGH, so the TX LED hooks are
  inverted relative to STM32Board's active-LOW default.
- 32 KB reserved at the top of flash for LittleFS, as on the other
  STM32WL variants.

Verified on hardware: all four environments build; repeater and room_server
flash and run over ST-LINK; identity and prefs persist across reboot and
across a firmware swap; and GPIOC reads back the documented RX levels at
idle, confirming the front-end switch is driven correctly.

Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
2026-11-04 09:46:40 -05:00
Will MacGregorandClaude Opus 5 287c5e21cf Enable simple_room_server on the STM32 platform
The room server gated its filesystem paths on NRF52_PLATFORM only, so an
STM32 build fell through to the ESP32 branch and failed to compile:

  MyMesh.cpp:147: no matching function for call to
    'Adafruit_LittleFS::open(const char*&, const char [2], bool)'
  main.cpp:69:   'store' was not declared in this scope

STM32 uses the same InternalFS / Adafruit_LittleFS API as nRF52, including
append semantics (FILE_O_WRITE opens LFS_O_RDWR|LFS_O_CREAT and then seeks
to the end), so the nRF52 branch is already correct for it. Add
STM32_PLATFORM alongside NRF52_PLATFORM in the four remaining gates;
saveIdentity() already did this.

This unblocks the room_server example on the existing STM32WL boards
(wio-e5-mini, wio-e5-dev, rak3x72, tiny_relay) as well as new ones.

Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
2026-11-04 09:46:27 -05:00
tthandClaude Opus 5.5 a8f0c3dca6 simple_room_server: dfu, radio silence watchdog and get boot via NodeMaintenance
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-04 01:25:27 +01:00
tthandClaude Opus 5.5 2ced8502a0 simple_repeater: dfu, radio silence watchdog and boot diagnostics from NodeMaintenance
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-04 00:38:43 +01:00
tthandClaude Opus 5.5 7159a00f05 simple_sensor: dfu, radio silence watchdog and get boot via shared NodeMaintenance
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-04 00:21:54 +01:00
tthandClaude Opus 5.5 278c1b8c8a simple_repeater: radio silence watchdog -- re-arm RX, then reboot a deaf receiver (#6)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-03 20:03:01 +01:00
nminaylov 38eb3d99e4 rpi_pico2 HW variant support 2026-11-03 14:50:29 +03:00
tthandClaude Opus 5.5 10f0349207 docs: dock-quiet is gone; BLE goes dark when another central holds the link; ble pin over the mesh
pub-release / release (push) Successful in 23m57s
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-03 01:47:27 +01:00
tthandClaude Opus 5.5 c1eaa6f98b simple_repeater: ble pin <6 digits> -- own BLE PIN, saved; public builds refuse ble on without it
pub-release / release (push) Successful in 23m33s
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-03 01:37:38 +01:00
tthandClaude Opus 5.5 1cfa726cdd README: flashing a release (web flasher, Custom Firmware) and the BLE PIN truth
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-03 01:20:16 +01:00
tthandClaude Opus 5.5 654d53f34c pub-release: observer variants of the nRF52 repeaters
pub-release / release (push) Successful in 26m19s
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-02 23:16:35 +01:00
tthandClaude Opus 5.5 94a5526b66 simple_repeater: RPT_BLE_DEFAULT_OFF -- BLE console starts off, ble on is saved
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-02 23:15:52 +01:00
tth ea1cf46cf4 Merge remote-tracking branch 'rfa/main' 2026-11-02 19:41:34 +01:00
tthandClaude Opus 5.5 f0c48e2b46 simple_repeater: RADIO_DIAG on the masts (radiostat/radiokick)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-02 19:41:29 +01:00
upstream-sync-bot 5dd6e7ac6a Merge upstream/dev (2 commits) [upstream-sync]
pub-release / release (push) Successful in 22m48s
2026-11-02 17:06:09 +00:00
tthandClaude Opus 5.5 548b96d15c simple_repeater: filter hash throttle + opt-in message age limit (tth #3)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-02 17:40:09 +01:00
tthandClaude Opus 5.5 e3029de6e4 pub-release: build the repeater's channel filter in (empty list)
pub-release / release (push) Successful in 20m2s
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-02 14:22:13 +01:00
tthandClaude Opus 5.5 88ef08c6d5 public builds: Czech mesh defaults (meshcore.cz wiki)
pub-release / release (push) Successful in 20m57s
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-02 14:15:14 +01:00
tthandClaude Opus 5.5 f7887324e5 public export runs after every upstream merge; pub-release on push
pub-release / release (push) Successful in 18m36s
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-02 11:48:48 +01:00
tthandClaude Opus 5.5 7508a94415 pub-release: public firmware builds for the published fork
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-02 11:08:16 +01:00