A cold start can take up to ~30 min with a weak sky view, so the default
limit before the first fix since boot goes from 15 min to 1 h.
The limit is now a GPS preference, set with `gps firstfix <duration>`
(0 = no limit, at most 1 day) and saved with the other GPS settings, so
repeaters and companions can use different values without a rebuild.
GPS_FIRST_FIX_TIMEOUT_MS stays as the build default.
The remote-CLI reply buffers in onPeerDataRecv() (repeater, room server,
sensor) and BaseChatMesh were sized temp[166] for a 5-byte datagram
header plus 161 bytes of reply. But MyMesh::handleCommand() first
reflects a 3-byte correlation prefix (e.g. 'aa|') into the reply, after
which CommonCLI commands may write up to 160 chars + NUL into the
remaining 158 bytes -- overflowing the buffer by 2 bytes (e.g. a full
'regions' listing via exportTo(reply, 160)).
Triggering this remotely crashes the node (observed as an unresponsive
repeater after a prefixed 'regions' query); the 2 out-of-bounds bytes
are a printable region-name character and a NUL.
Size the buffers for the full worst case instead:
5 header + 3 prefix + 160 reply + 1 NUL = 169.
Verified with a host ASan harness reproducing the exact layout:
prefixed 'regions' with a 25-region listing overflowed temp[166]
(BufStream::write, RegionMap.cpp) and now passes clean with temp[169];
unprefixed (serial) path unaffected.
Repeaters, room servers and sensors already let the battery ADC multiplier be tuned with 'set adc.multiplier' (CommonCLI). The companion firmware had no equivalent, so a board whose divider differs from the build default (common on DIY ProMicro / Faketec boards) always reported a wrong battery voltage.
Adds the same command to the companion CLI. The value is stored in the companion prefs (comp.adc_mult, 0 = board default) and applied at startup via MainBoard::setAdcMultiplier().
Move TimeSeriesData from simple_sensor into src/helpers and drive it with
monotonic uptime, so RTC changes cannot stall recording or break queries.
Keep the old RTCClock* overloads as deprecated for custom sensor sketches.
Record 24h of battery, noise floor, TX/RX airtime % and MCU temperature on
repeaters and answer the existing 0x04 min/max/avg request using the same
format as sensor nodes. No packets are sent by this feature.
REPEATER_HISTORY_SLOTS=0 removes it; default off on STM32/RP2040.
Add native tests for TimeSeriesData and document the request and channels.
The room server gated its filesystem paths on NRF52_PLATFORM only, so an
STM32 build fell through to the ESP32 branch and failed to compile:
MyMesh.cpp:147: no matching function for call to
'Adafruit_LittleFS::open(const char*&, const char [2], bool)'
main.cpp:69: 'store' was not declared in this scope
STM32 uses the same InternalFS / Adafruit_LittleFS API as nRF52, including
append semantics (FILE_O_WRITE opens LFS_O_RDWR|LFS_O_CREAT and then seeks
to the end), so the nRF52 branch is already correct for it. Add
STM32_PLATFORM alongside NRF52_PLATFORM in the four remaining gates;
saveIdentity() already did this.
This unblocks the room_server example on the existing STM32WL boards
(wio-e5-mini, wio-e5-dev, rak3x72, tiny_relay) as well as new ones.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>